Connection cable between the electronic ballast and the mains. An easy and safe way to connect these devices, with high durability thanks to the pre-injected plug. The plug is made of PVC and copper foil and is rated to withstand 10A and 250V.
The cable is made of PVC.

Length 3m x 1.55m

Connector to make the connections of transformers and parabolic reflectors without having to cut cables. To connect the Plug & Play, a 1.5 mm diameter electric wire is recommended.

2 meters long cable with injected shuco plug. It can be used to connect the power supply to the domestic socket or any other element such as air extractors, fans, control units, etc...

Schuko plug to be wired for a maximum load of 230V/16A in white color and type DE.

Multiple base with lid and 6-place electric cable.
Maximum power 3500 W- 16 A- 250 V.

100 meter 3pole x 2.5 mm electric cable coil.

The RJ14 interconnect cable is used to connect the Gavita Master Controller , with additional power supplies (in series). It can be connected in series, so that when the controller senses that they need to be turned on, it emits a low intensity signal that turns on the equipment.
Made with quality materials, strong and durable.
Length:2.4 Meters

Cable to connect the led bar

Power cable to connect the Sanlight Q-Series to the mains. These cables are only compatible with Sanlight Q-series.
Length:2 Meters.

Extension cable for making connections between the various Sanlight Q-Series appliances. These cables allow you to connect your LED equipment and fully customize your lighting system and fit your grow space.

Dimmer compatible with Sanlight Q-Series LED systems. This add-on allows you to get the most out of your LED system.
A dimmer is required for each lamp.

Extension cable to make connections between different Sanlight FLEX equipment. These cables allow you to connect your LED equipment and fully customize your lighting system and adapt it to your grow space.
Length :1 Meter

Roll for 1.5 mm2 cable, three wires of 100 meters. Suitable for operation of sodium vapor lamps up to 600W .Type: H05 RR-F 3G1,5mm

Male/female connection cable for electronic ballast and network. An easy and safe way to connect these devices, with high durability thanks to the pre-injected plug. The plug is made of PVC and copper foil and is rated to withstand 10A and 250V.
The cable is made of PVC.

Length 4 m x1,55

Male connection cable with unsheathed socket wires for electronic ballast and mains. An easy and safe way to connect these devices, with high durability thanks to the pre-injected plug. The plug is made of PVC and copper foil and is rated to withstand 10A and 250V.
The cable is made of PVC.

Length 1.5m

Dimlux connection cable to connect DimLux projectors to the Dimlux Maxi Controller and other Dimlux projectors. This Dimlux Interlink cable has a plug at both ends.
10 meter length

With this temperature sensor, the Maxi Controller can dim the lighting according to the temperature. If the set value is exceeded, the regulation is activated first to keep the temperature under control. If the temperature rises despite dimming, half of the dimmed lights go out, if the temperature continues to rise all lights go out for at least 20 minutes.
Length:5 meters

This humidity sensor connected to the Maxi Controller can activate/deactivate a humidifier, based on the relative humidity levels within the growing area. If you need to view the Vapor Pressure Deficit (VPD), you will also need the plant temperature camera.
10 meter length

The LUMii Reflector Extension or Extension Cable is suitable for use with all LUMii and IEC reflectors. Make sure that when using extension cords for HID, the transformer is designed to operate the lamp over long distances.
PowerPlant and LUMii ballasts are capable of lighting a lamp up to 1.5 meters from the transformer (maximum).

This 5 m long LED interconnect cable is designed to connect LUMATEK controllable LED devices allowing a stable and precise connection without any interference. Just connect the M12 self-locking male plug to the output of the Signal Out LED structure and the M12 self-locking female plug to the input of the Signal In LED structure of the next device.

These two 5m long extension cables are designed to connect the Lumatek driver and the LED fixture, in case the driver is used remotely and away from the fixture. Allowing a stable and precise connection without any interference this product is made up of 2 elements:

• 5 m extension power cable for Led driver

• 5 m LED dimming cable

Reinforced bracket with E40 ceramic socket with power socket and 1.5 meter cable, ideal for replacing and/or creating new lamp holders or sockets.

Reinforced bracket with E40 ceramic socket and 4 meter cable, ideal for replacing and/or creating new lamp holders or sockets.

The LUMii Cord Set offers 4 meters of IEC cable and a ceramic lamp holder with E40 socket, for HPS, MH and AGRO lamps. Ideal for hanging indoor grow lights in the Grow Box/Grow Room, if you don't plan to use a reflector, we recommend using the LUMII Cord Set 4m in combination with the LUMii Hanging Bracket.
IEC socket connection
Suitable for lamps up to 600W